描述

含阻燃剂的尼龙66 PA66 CF45

规格

碳纤维增强聚酰胺尼龙PA6 PA66

高机械强度，

高软化温度，

耐热性

工程塑料PA66颗粒CF30性能：

PA具有机械强度高、软化点高、耐磨性好、

自润滑、缓冲、隔音、优异的耐油性和化学腐蚀性，以及良好的电气绝缘性。由于这些优越的性能，PA复合材料已经取代了一些金属作为结构材料

尼龙66 PA66 CF45阻燃剂

产品详细信息

碳纤维45%耐磨导电尼龙

PA66型材：

PA66聚酰胺66或尼龙66在聚酰胺材料中具有高熔点。它是一种半结晶材料。PA66可以在较高温度下保持强大的强度和刚度。在产品设计中，必须考虑吸湿对几何稳定性的影响。经常添加各种改性剂以改善PA66的机械性能。玻璃是最常见的添加剂，有时添加合成橡胶，如EPDM和SBR，以提高抗冲击性。PA66的粘性较低，因此流动性良好（但不如PA6）。此特性可用于制作非常薄的组件。它的粘度对温度变化很敏感。PA66的收缩率在1%到2%之间。加入玻璃纤维添加剂可使收缩率降低到0.2%～1%。在流动方向和流动方向的垂直方向上收缩更大。PA66耐多种溶剂，但不耐酸和其他氯化剂

更多详细信息，请联系：电子邮件：####

工艺条件：

干燥处理：如果材料在加工前密封，则无需干燥。但是，如果打开储存容器，建议在85℃的热风干燥过程中进行干燥。如果湿度大于0.2%，仍需在105℃下真空干燥12小时

熔融温度：260~290℃。玻璃添加剂产品适用于275~280℃。熔化温度应避免高于300℃。模具温度：建议为80℃。模具温度会影响结晶度，结晶度会影响产品的物理性能。对于薄壁塑料件，如果使用的模具温度低于40℃，塑料件的结晶度会随着时间的推移而变化，为了保持塑料件的几何稳定性，需要进行退火处理

注射压力：通常在750到1250bar之间，取决于材料和产品设计

注射速度：高速（对于增强型材料略低）。浇口和浇口：由于PA66的固化时间很短，浇口的位置非常重要。闸门孔径不应小于0.5t（其中t是塑料件的厚度）。如果使用热流道，浇口尺寸应小于常规流道，因为热流道有助于防止材料过早凝固。如果使用水下闸门，闸门的最小直径应为0.75mm。PA66更广泛地应用于汽车工业、仪表外壳和其他要求抗冲击性和高强度的产品中。透明或不透明的乳白色结晶聚合物，具有可塑性。密度为1.15 g/cm3。熔点为252℃。脆性温度30℃。热分解温度大于350℃。连续加热80-120℃，平衡吸水率为2.5%。耐酸、碱、大多数无机盐溶液、卤代烃、碳氢化合物、酯、酮等腐蚀。

特点：

1。优异的耐磨性、自润滑性和机械强度。然而，由于吸收性较大，尺寸稳定性较差。PA66可在较高温度下保持强大的强度和刚度。PA66成型后仍具有吸湿性，其吸湿程度主要取决于材料组成、壁厚和环境条件

3。在产品设计中，必须考虑吸湿对几何稳定性的影响。经常添加各种改性剂以改善PA66的机械性能。玻璃是最常见的添加剂，有时添加合成橡胶，如EPDM和SBR，以提高抗冲击性。PA66的粘性较低，因此流动性良好（但不如PA6）。此特性可用于制作非常薄的组件。它的粘度对温度变化很敏感

4。PA66的收缩率在1%到2%之间。加入玻璃纤维添加剂可使收缩率降至0.2%～1%。在流动方向和流动方向的垂直方向上收缩更大。PA66耐多种溶剂，但不耐酸和其他氯化剂

优点：

1。高抗拉强度

2。优异的韧性和抗冲击性

3。良好的自润滑性、耐磨性和抗药性

4。优良的低温特性

5。自熄

用途：

广泛应用于机械、仪表、汽车零部件、电子电气、铁路、家电、通讯、纺纱机、体育休闲用品、油管、油箱等精密工程产品。电气和电子设备：连接器、拨禾轮轴、定时器、盖断路器、开关箱汽车：冷却风扇、门把手、油箱盖、进气栅栏、水箱盖、灯座工业零件：座椅、自行车车架、滚轮鞋底、纺织梭子、踏板

Nylon66 PA66 CF45 With Flame Retardant

Specifications
Carbon fiber reinforced Polyamide Nylon PA6 PA66
high mechanical strength,
high softening temperature,
heat resistance.
Engineering Plastic PA66 Granules CF30 Property:
PA has the advantages of high mechanical strength, high softening point, good wear resistance,
self-lubrication, cushioning, sound deadening, excellent oil and chemical corrosion resistance, and good
electrical insulation. Because of these superior performances, PA composite has already replaced some
metals being as structural materials.

Nylon66 PA66 CF45 With Flame Retardant

Product Details

Carbon fiber 45% wear – resistant conductive nylon

PA66 profile:

PA66 polyamide 66 or nylon 66 has high melting point in polyamide materials.It is a semi-crystalline – crystalline material.PA66 can maintain strong strength and stiffness at higher temperatures.In product design, the influence of moisture absorption on geometric stability must be considered.Various modifiers are often added to improve the mechanical properties of PA66.Glass is the most common additive, and sometimes synthetic rubber, such as EPDM and SBR, is added to improve impact resistance.The stickiness of PA66 is low, so liquidity is good (but not as good as PA6).This property can be used to make very thin components.Its viscosity is sensitive to temperature changes.The shrinkage rate of PA66 is between 1% and 2%. Adding glass fiber additives can reduce the shrinkage rate to 0.2%~1%.Shrinkage is greater in the direction of the flow and vertical direction of the flow direction.PA66 is resistant to many solvents but is less resistant to acids and other chlorinated agents.

Any more details,please contat at : Email : ###

Process conditions:

Dry treatment: there is no need to dry if the material is sealed before processing.However, if the storage container is opened, it is recommended that the at 85 ℃ hot air drying process.If the humidity is more than 0.2%, still need to be 105 ℃, 12 hours of vacuum drying.

Melting temperature: 260 ~ 290 ℃.Glass additives products for 275 ~ 280 ℃.Melting temperature should avoid higher than 300 ℃.Mold temperature: it is recommended that 80 ℃.The mold temperature will affect the crystallinity, which will affect the physical properties of the product.For thin wall plastic parts, if you use the mold temperature below 40 ℃, the plastic parts of crystallinity will change over time, in order to keep the geometric stability of the plastic parts, annealing treatment is required.

Injection pressure: usually between 750 and 1250bar, depending on the material and product design.

Injection speed: high speed (slightly lower for enhanced materials).Runner and gate: since the solidification time of PA66 is very short, the location of gate is very important.Gate aperture should not be less than 0.5t (where t is the thickness of the plastic part).If a hot runner is used, the gate size should be smaller than a regular runner because the hot runner helps prevent material from solidifying prematurely.If a submerged gate is used, the minimum diameter of the gate should be 0.75mm.PA66 is more widely used in the automotive industry, instrument housing and other products requiring impact resistance and high strength requirements.Transparent or opaque opalescent crystalline polymer with plasticity.Density of 1.15 g/cm3.Melting point is 252 ℃.Brittle temperature 30 ℃.The thermal decomposition temperature greater than 350 ℃.Continuous heat 80-120 ℃, balance the bibulous rate is 2.5%.Resistant to corrosion by acid, alkali, most inorganic salt solutions, halonates, hydrocarbons, esters, ketones, etc.

Features:

1.Excellent wear resistance, self-lubricating and mechanical strength.However, due to larger absorbency, the dimensional stability is poor

2. PA66 can maintain strong strength and stiffness at a higher temperature.PA66 is still hygroscopic after forming, and its degree mainly depends on the material composition, wall thickness and environmental conditions.

3. In product design, the influence of moisture absorption on geometric stability must be considered.Various modifiers are often added to improve the mechanical properties of PA66.Glass is the most common additive, and sometimes synthetic rubber, such as EPDM and SBR, is added to improve impact resistance.The stickiness of PA66 is low, so liquidity is good (but not as good as PA6).This property can be used to make very thin components.Its viscosity is sensitive to temperature changes.

4. The shrinkage rate of PA66 is between 1% and 2%. Adding glass fiber additive can reduce the shrinkage rate to 0.2%~1%.Shrinkage is greater in the direction of the flow and vertical direction of the flow direction.PA66 is resistant to many solvents but is less resistant to acids and other chlorinated agents.

Advantages:

1. High tensile strength;

2. Excellent resistance to toughness and impact;

3. Good self-lubrication, wear resistance and drug resistance;

4. Excellent low temperature characteristics;

5. Self-extinguishing;

Application:

It is widely used in machinery, instrument, automobile parts, electronic and electrical, railway, household appliances, communication, spinning machine, sports and leisure products, oil pipe, oil tank and some precision engineering products.Electrical and electronic equipment: connector, reel shaft, timer, cover breaker, switch housingAutomobile: cooling fan, door handle, oil box cover, air intake fence, water tank cover, lamp holderIndustrial parts: chair seats, bicycle frames, roller shoe soles, textile shuttles, pedals