描述

电机外壳用尼龙66 Gf30%FR V0。工程尼龙，改性PA66颗粒
2。耐磨、热稳定性、高刚性、增韧，
3。高冲击、高滑动、高流动、高光泽、耐候性
4。对于我们的增强尼龙系列，填充率为10%-50%<尼龙66、尼龙66、聚酰胺66

电机外壳用尼龙66 Gf30%FR V0

产品详细信息

<。与PA6相比，PA66更广泛地应用于汽车工业、仪表外壳和其他要求抗冲击性和高强度的产品中

广泛用于制造机械、汽车、化工和电气零件，如齿轮、滚柱、滑轮、滚柱、泵叶轮、风机叶片、高压密封外壳、阀座、垫片、衬套、各种手柄、支架、电线包内层、，尼龙66 gf30%FR v0用于电机外壳

工艺条件：尼龙66 gf30%FR v0

干燥：如果材料在加工前密封，则无需干燥。但是，如果打开储存容器，建议在85°C的热空气中干燥。如果湿度大于0.2%，则需要在105°C下真空干燥12小时。尼龙66 gf30%FR v0熔融温度：260~290℃。玻璃添加剂的产品温度为275~280℃。熔化温度应避免超过300°C。模具温度：建议为80°C。模具温度会影响结晶度，结晶度会影响产品的物理特性。对于薄壁塑料零件，如果使用低于40°C的模具温度，塑料零件的结晶度将随时间变化。为了保持塑料零件的几何稳定性，需要进行退火处理。尼龙66 gf30%FR v0注射压力：通常为750~1250bar，具体取决于材料和产品设计。尼龙66 gf30%FR v0

优点：

1。有竞争力的价格、高品质、准时交货、免费样品

<跨度>2。环保

3。高机械强度，高光泽4。更好的韧性和表面

<跨度>5。可使用玻璃纤维/韧性/阻燃剂/紫外线稳定剂进行加固

有关电机外壳用尼龙66 gf30%FR v0的任何问题，请直接联系我们<现在联系：特蕾西

Nylon66 Gf30% FR V0 For Motor Housing

1.Engineering Nylon ,Modified PA66 Granules
2.Wear resistant,Thermal stability,High rigidity,Toughened,
3.High impact,High sliding,High Flow,High gloss,Weather resistan
4.For our Reinforced Nylon series, filling 10%-50%.
Nylon 66,pa66 ,polyamide 66

Nylon66 Gf30% FR V0 For Motor Housing

Product Details

Nylon66 gf30% FR v0 For motor housing

PA66 (polyamide 66 or nylon 66). Compared with PA6, PA66 is more widely used in the automotive industry, instrument housings, and other products that require impact resistance and high strength.

Widely used in the manufacture of mechanical, automotive, chemical and electrical parts, such as gears, rollers, pulleys, rollers, pump impellers, fan blades, high-pressure seal enclosures, valve seats, gaskets, bushings, various Handle, support, inner layer of wire package, etc.Nylon66 gf30% FR v0

Nylon 66 GF30% FR v0 for motor housing

Process conditions:Nylon66 gf30% FR v0

Drying: If the material is sealed before processing, then there is no need to dry. However, if the storage container is opened, it is recommended to dry it in hot air at 85 ° C. If the humidity is greater than 0.2%, vacuum drying at 105 ° C for 12 hours is required.Nylon66 gf30% FR v0

Melting temperature: 260 ~ 290 ℃. The product for glass additives is 275 ~ 280 ℃. The melting temperature should be avoided above 300 ° C. Mold temperature: 80 ° C is recommended. The mold temperature will affect the crystallinity, and the crystallinity will affect the physical characteristics of the product. For thin-walled plastic parts, if a mold temperature lower than 40 ° C is used, the crystallinity of the plastic parts will change with time. In order to maintain the geometric stability of the plastic parts, annealing treatment is required.Nylon66 gf30% FR v0

Injection pressure: usually 750 ~ 1250bar, depending on material and product design.Nylon66 gf30% FR v0

Any questions about Nylon66 gf30% FR v0 for motor housing,please contact us directly.Contact Now：Tracy <###>