描述
PC的主要性能特点：无卤阻燃，高流动性，高耐热性
用途：显示屏前框、后壳、笔记本电脑壳、电子电器等。
PC主要性能
产品详细信息
电脑主要性能
电脑主要性能
1。机械性能：高强度、抗疲劳性、尺寸稳定性和小蠕变（在高温条件下几乎没有变化）
2。耐热老化：增强的UL温度指数达到120~140℃（长期户外老化也很好）
3。耐溶剂性：无应力开裂
4。水稳定性：在高温下易在水中分解（在高温高湿环境中慎用）
5。电气性能：6。绝缘性能：优异（湿度和高温能保持稳定的电气性能，是制造电子电气零件的理想材料）
7。介电系数：3.0-3.2
8。电弧电阻：120s
9。成型加工性：普通设备注塑或挤出
PC塑料粘接
根据不同的需要，可以选择以下粘合剂：
1。G-933：单组分室温固化软弹性防震胶，耐高温和低温，不同粘度的粘接速度在几秒钟到几小时内固化
2。KD-833即时胶可以在几秒钟或几十秒钟内快速粘合PC塑料，但粘合层坚硬易碎，不耐60度以上的热水浸泡
电脑的主要性能。QN-505，双组分胶，软胶层，适用于PC塑料的大面积粘接或复合。但耐高温性较差
4。QN-906：双组分胶水，耐高温
5。G-988：单组分室温硫化橡胶，固化后的弹性体具有优异的防水、防震胶、耐高低温性能，如果厚度为1-2mm，大约10分钟即可固化，5-6小时基本固化，有一定的强度。完全治愈至少需要24小时。单组分，无需混合，挤出后涂抹，不用加热即可
6。KD-5606：紫外光固化胶粘剂，粘接透明PS板材和板材，可达到无痕迹效果，需要紫外光固化。粘贴后效果很好。但耐高温性较差
<
请立即联系，以获取有关电脑主要性能的详细信息
是一家专业的pc主机性能制造商，您可以从我们工厂以优惠的价格订购高质量的pc主机性能
PC Main Performance
Features: halogen-free flame retardant,
high fluidity, high heat resistance.
Application: display front frame and back shell,
notebook shell, electronic appliances, etc.
PC Main Performance
Product Details
PC main performance
1. Mechanical properties: high strength, fatigue resistance, dimensional stability, and small creep (very few changes under high temperature conditions);
2. Heat aging resistance: the enhanced UL temperature index reaches 120~140℃ (long-term outdoor aging is also very good);
3. Solvent resistance: no stress cracking;
4. Water stability: it is easy to decompose in water at high temperature (use caution in high temperature and high humidity environments);
5. Electrical performance:
6. Insulation performance: excellent (humidity and high temperature can maintain stable electrical performance, it is an ideal material for manufacturing electronic and electrical parts);
7. Dielectric coefficient: 3.0-3.2;
8. Arc resistance: 120s;
9. Molding processability: ordinary equipment injection or extrusion.
PC plastic bonding
According to different needs, the following adhesives can be selected:
1. G-933: One-component room temperature curing soft elastic shockproof adhesive, high and low temperature resistance, different viscosity bonding speed in a few seconds to a few hours to cure.
2. KD-833 instant adhesive can quickly bond PC plastic in a few seconds or tens of seconds, but the adhesive layer is hard and brittle, and it is not resistant to hot water immersion above 60 degrees.
PC main performance
3. QN-505, two-component glue, soft glue layer, suitable for large area bonding or compounding of PC plastic. But the high temperature resistance is poor.
4. QN-906: Two-component glue, high temperature resistance.
5. G-988: One-component room temperature vulcanized rubber, after curing, the elastomer has excellent waterproof, shockproof adhesive, high and low temperature resistance, if the thickness is 1-2mm, it will be cured in about 10 minutes, and basically cured in 5-6 hours , There is a certain strength. It takes at least 24 hours to fully cure. Single-component, no need to mix, just apply after extruding and let it stand without heating.
6. KD-5606: UV curing adhesive, bonding transparent PS sheet and board, can achieve no trace effect, need to be cured by ultraviolet light. The effect is beautiful after sticking. But the high temperature resistance is poor.
.
Contactnowformoredetailsabout PC main performance.
Kitty Liu< ###>
is one of the professional pc main performance manufacturers, you can order high quality pc main performance at good price from our factory.
评价
目前还没有评价