描述
推广Pps塑料聚苯硫醚（Pps）Pps树脂颗粒价格
产品名称：聚苯硫醚（PPS）
颜色：根据需要
优点：价格优惠、质量高、交货及时、免费样品、环保
无任何杂质
可使用30%至70%的玻璃纤维加固
包装：25kg/袋（也可定制）
推广Pps塑料聚苯硫醚（Pps）Pps树脂颗粒价格
产品详细信息
推广pps塑料聚苯硫醚（pps）pps树脂颗粒价格
成型注意事项
注意以下事项和材料安全数据表。据我们所知，此处包含的信息是准确的。然而，制造商对本文所含信息的准确性或完整性不承担任何责任
1。颗粒的预干燥
超过干燥温度和/或时间会导致颜色变化或流动性变化
2。最合适的钢瓶温度范围为300至340˚C，加热温度不得超过350˚C。然而，最合适的钢瓶温度。应确认PPS等级。尤其是出于安全考虑，填充PTFE*的牌号的温度范围应为290至320˚C，且加热温度不得超过330˚C.
3。气缸中的停留时间
以下给出了一个标准，可能因DIC等级而异。PPS和不同的条件。300˚C：小于60分钟。
320˚C：小于30分钟。
4。树脂降解或分解
如果树脂降解或分解或担心分解，降低气缸温度并清除树脂
5。关闭当关闭操作时，彻底清除树脂并关闭加热器
6。不要将着色剂、添加剂或其他树脂与PPS混合，DIC推荐的材料除外
7。为了操作期间的安全7─1.建议使用通风系统，
对于填充聚四氟乙烯的等级尤其必要
7─2.戴护目镜和手套
7─3.让操作员远离喷嘴部分
7─4.未戴手套时，不得接触熔融树脂
8。处置方法
根据当地法规，在安全条件下处置或焚烧
是专业推广pps塑料聚苯硫醚（pps）树脂颗粒的厂家之一，您可以从我厂以优惠的价格订购优质的推广pps塑料聚苯硫醚（pps）树脂颗粒
Promotion Pps Plastic Polyphenylene Sulfide (pps) Pps Resin Pellet Price
.
Product Name: PPS
Color : As required
Advantage: Competitive price, high quality, on-time delivery, free sample,Environment friendly
Without any impurity
Can be reinforced with the glass fiber from 30% to 70%
Packing : 25kg/bag(also customizable)
Promotion Pps Plastic Polyphenylene Sulfide (pps) Pps Resin Pellet Price
Product Details
Promotion pps plastic polyphenylene sulfide (pps) pps resin pellet price
Precautions for molding
Be aware of the followings and the Material Safety Data Sheet. And to the best of our knowledge, the information contained herein is accurate. However, the manufacturers do not assume any liability whatsoever for the accuracy or completeness of the information contained herein.
1. Pre-drying of pellets
Excess of drying temperature and/or time would be caused a color change or change of flow ability.
2. Suitable cylinder temperature Range of the most suitable cylinder temperature is 300 to 340˚C and do not heat over 350˚C. However, most suitable temperature . PPS grades should be confirmed. Especially for safety, the temperature range of the grades which are filled PTFE* should be 290 to 320˚C and do not heat over 330˚C.
3. Residence time in cylinder
The followings give a standard, and may vary on grades of DIC.PPS and different conditions. 300˚C: less than 60 min.
320˚C: less than 30 min.
4. Degradation or decomposition of resin
In case of degradation or decomposition of resin or any fear of decomposition, reduce the cylinder temperature and purge the resin out.
5. Shutting down When shutting down the operation, purge resin out completely and the heater off.
6. Do not mix colorants, additives or other resins with PPS except materials which DIC recommends.
7. For safety during operation7─1. Ventilation system is recommended and
especially is necessary for PTFE filled grades.
7─2. Wear protective goggles and gloves.
7─3. Keep operator away from nozzle section.
7─4. Do not touch molten resin without gloves.
8. Disposal method
Dispose or incinerate under safe conditions of in accordance with local regulations.
is one of the professional promotion pps plastic polyphenylene sulfide (pps) pps resin pellet price manufacturers, you can order high quality promotion pps plastic polyphenylene sulfide (pps) pps resin pellet price at good price from our factory.
推广pps塑料聚苯硫醚（pps）pps树脂颗粒价格
注意以下事项和材料安全数据表。据我们所知，此处包含的信息是准确的。然而，制造商对本文所含信息的准确性或完整性不承担任何责任
1。颗粒的预干燥
超过干燥温度和/或时间会导致颜色变化或流动性变化
2。最合适的钢瓶温度范围为300至340˚C，加热温度不得超过350˚C。然而，最合适的钢瓶温度。应确认PPS等级。尤其是出于安全考虑，填充PTFE*的牌号的温度范围应为290至320˚C，且加热温度不得超过330˚C.
以下给出了一个标准，可能因DIC等级而异。PPS和不同的条件。300˚C：小于60分钟。
320˚C：小于30分钟。
4。树脂降解或分解
如果树脂降解或分解或担心分解，降低气缸温度并清除树脂
6。不要将着色剂、添加剂或其他树脂与PPS混合，DIC推荐的材料除外
7。为了操作期间的安全7─1.建议使用通风系统，
对于填充聚四氟乙烯的等级尤其必要
7─2.戴护目镜和手套
7─3.让操作员远离喷嘴部分
7─4.未戴手套时，不得接触熔融树脂
8。处置方法
Product Name: PPS
Color : As required
Advantage: Competitive price, high quality, on-time delivery, free sample,Environment friendly
Without any impurity
Can be reinforced with the glass fiber from 30% to 70%
Packing : 25kg/bag(also customizable)
Be aware of the followings and the Material Safety Data Sheet. And to the best of our knowledge, the information contained herein is accurate. However, the manufacturers do not assume any liability whatsoever for the accuracy or completeness of the information contained herein.
1. Pre-drying of pellets
Excess of drying temperature and/or time would be caused a color change or change of flow ability.
2. Suitable cylinder temperature Range of the most suitable cylinder temperature is 300 to 340˚C and do not heat over 350˚C. However, most suitable temperature . PPS grades should be confirmed. Especially for safety, the temperature range of the grades which are filled PTFE* should be 290 to 320˚C and do not heat over 330˚C.
The followings give a standard, and may vary on grades of DIC.PPS and different conditions. 300˚C: less than 60 min.
320˚C: less than 30 min.
4. Degradation or decomposition of resin
In case of degradation or decomposition of resin or any fear of decomposition, reduce the cylinder temperature and purge the resin out.
6. Do not mix colorants, additives or other resins with PPS except materials which DIC recommends.
7. For safety during operation7─1. Ventilation system is recommended and
especially is necessary for PTFE filled grades.
7─2. Wear protective goggles and gloves.
7─3. Keep operator away from nozzle section.
7─4. Do not touch molten resin without gloves.
8. Disposal method
评价
目前还没有评价